How repair works/Ventura County/9 min read
Auto Body Repair: When a Panel Gets Fixed and When It Gets Replaced.
Replace, or repair? On a mild-steel outer skin it is a judgment call. On an ultra-high-strength rail the automaker has already made it.
Two dents can look identical from the driveway. One gets worked out and sent home, the other gets a brand new part and a longer wait. In auto body repair, the difference is the metal, the shape of the damage and a factory rule written before your car ever left the plant.
- Since 1965Family owned, Oxnard & Ventura
- I-CAR Gold Class & PlatinumContinuous training, checked every year
- 13 manufacturer programmesHonda, Acura, Ford, Subaru, GM, Cadillac, FCA, Hyundai, Kia, Rivian, Lucid, Tesla & VinFast
- Repair or replace is decided by what the part is made of, how sharply it is bent and what the automaker’s procedure allows.
- A gradual bend can often be straightened. A sharp kink usually means a new part.
- On ultra-high-strength steel, the automakers below say no heat, and several say no straightening at all. Damaged often means replaced.
- Estimating databases price replacement on a new, undamaged car, which is why repair lines on an estimate get negotiated.
A runaway shopping cart at The Collection at RiverPark does not care what your car is made of. Your repair shop has to.
Take two dents of the same size. One is in the outer skin of a door, a thin panel of ordinary steel that was designed to be worked back into shape. The other is in a structural rail made of a steel so strong the automaker has banned anyone from straightening it. From the parking lot they look like twins. On the estimate they are strangers.
This is how auto body repair decisions actually get made, and why “can’t you just pull that out?” has a longer answer than it used to. We fix cars; nothing here is legal advice.
The metal decides first
Cars used to be built mostly out of mild steel, which is forgiving. Bend it, pull it, heat it a little, and it goes back more or less where it was. That era is over. When Jason Bartanen, I-CAR’s industry technical relations director, explained in 2017 why the old kink-versus-bend rule was fading, his answer was short: “We don’t work on mild steel vehicles anymore.”
Modern bodies mix mild steel, high-strength steel, ultra-high-strength steel and aluminum, sometimes all within arm’s reach of each other. The strength of steel is measured in megapascals, or MPa. In a body shop, it is the number that decides whether the next tool is a hammer or a purchase order.
The numbers climb fast. I-CAR’s rule is blunt: “Do not straighten parts that are above 600 MPa unless specific documentation exists from the OEM.” Meanwhile Honda says every Honda and Acura platform now includes 1,500 MPa ultra-high-strength steel in the body structure. That is the steel that keeps the cabin in one piece in a crash, and it is exactly the steel you do not want someone improvising on.
Bend or kink: the old rule and its fine print
For decades the shop floor ran on one simple rule. I-CAR defines a kink as “a sharp bend with a small radius over a short distance” and a bend as “a gradual change in shape between the damaged and undamaged area.” Kinked parts get replaced. Bent parts may be repaired.
It is a good rule. It is also no longer the final word, because the automaker outranks it.
I-CAR Repairability Technical Support — Kink vs. Bend, July 2017
“If the OEM states that a certain metal or part shouldn’t be straightened, then that part should be replaced (even if it’s only bent).”
In other words, the shape of the damage gets a vote. The manufacturer gets a veto.
The heat rule: the shortcut the factory took away
A torch is the fastest tool in a body shop and, on the wrong steel, the most expensive one. Heat can relax metal so it is easier to pull back into shape. On high-strength steels it can also permanently weaken the material, which you would never see and your car would never mention until the next crash.
This is what the automakers Tony’s is certified with actually say:
- Honda and Acura: Honda’s Summer 2026 repair newsletter says “any UHSS component that has had heat or cold straightening applied during repair must be replaced with a new part,” and that high-strength steel parts over 590 MPa must not be straightened.
- Chrysler, Dodge, Jeep, Ram and Fiat: FCA’s December 2025 position statement says that if heat is used to straighten structural high-strength, advanced high-strength or ultra-high-strength steel, “the component must be replaced.” Cold straightening is allowed without replacement.
- GM: On ultra-high-strength and dual-phase steel, heat is not recommended. On mild steel and HSLA steel, controlled heat is allowed up to 650°C (1200°F), a maximum of two times, for up to 90 seconds. Those are the limits a shop in GM’s Collision Repair Network works inside.
- Kia: Hot-stamped ultra-high-strength steel, once deformed, cannot be corrected and must be replaced as an assembly.
- Subaru: No heat shaping or splice welding on components made of 980 MPa class steel or stronger. That rule follows every Subaru into our Subaru auto body shop.
- Tesla: On the Model Y cast underbody, bent tabs can be straightened cold. Heat is off the table.
Every one of those rules is about the next crash. None of them is about how the dent looks.
Two shops, one phone call
Get the fix-or-replace call in writing.
Estimates and collision repair at Oxnard and Ventura. Manufacturer-certified repairs are completed at Oxnard; VinFast certified repairs at Ventura. If your car is estimated at one and needs the other, we move it at no charge to you.
Aluminum: different metal, different room
An aluminum body, masked for paint with the bumper cover off. Aluminum panels can be repaired, but only inside the automaker’s procedure, in a room steel dust cannot reach.
Aluminum plays by its own rules. It does not respond to a pull the way steel does, and a stray fleck of steel grinding dust embedded in bare aluminum can start a galvanic corrosion problem that shows up years later. Ford’s October 2025 position statement recommends that all Ford vehicles with aluminum structural or cosmetic panels “be repaired at an aluminum structural certified collision center.”
Whatever you drive, aluminum work needs its own space, its own air and its own tools. Ours is the fully enclosed aluminum room at Oxnard, which runs on filtered, positive-pressure air. If you drive a Rivian, the repair-or-replace question gets even more specific, and Rivian’s own repair procedures set the rules.
What your estimate is really saying
Estimates are built with databases from companies like CCC and Mitchell. They are useful, and they have a quirk most car owners never hear about. Mitchell’s own estimating guide says its labor times are for “replacement with new, undamaged parts from the vehicle manufacturer on a new, undamaged vehicle.” Anything extra, like access time or alignment pulls, “should be agreed upon by all parties.”
So “replace” comes with a number from the book. “Repair” comes with a number from a human who looked at your specific dent. The Society of Collision Repair Specialists puts it plainly: the databases are intended to be used as “a guide only.”
That is why, in auto body repair, the repair lines are the ones that get debated between the shop and the insurer. Mitchell data published in Enlyte’s 2026 trends report shows the share of parts repaired rather than replaced rose to 15.5% in 2025 from 14.8% in 2024, after more than 10 years of decline. The same report found that drivable repairs under $5,000 finished about eight-tenths of a day faster when the estimate included at least one repair line. Sometimes fixing the part really is the quicker road.
The question to ask your estimator
“What is this part made of, and what does the factory procedure say to do with it?”
Before any of that gets decided on a structural part, the car gets measured. Our structural equipment checks length, height and width against factory specifications, so the fix-or-replace call is based on the bench readout. What actually happens at an auto body shop shows where that step sits in the whole repair.
New part, but which new part?
When the answer is replace, there is one more decision: an OEM part from the automaker or an aftermarket part from someone else.
California has rules on this too. Under 10 CCR 2695.8(g), an insurer can only require non-OEM crash parts if they are “at least equal to the original equipment manufacturer parts in terms of kind, quality, safety, fit, and performance.” The insurer also has to pay for any modifications the part needs and warrant it in writing on the estimate. The Department of Insurance has even said estimates cannot use fuzzy labels like “Optional OEM” or “Alternate OEM.” Each part is either OEM or it is not. What Honda, Toyota, Subaru and Ford say about the choice is in OEM vs aftermarket parts.
On the parts count, CCC’s full-year 2025 data shows the average repairable appraisal used 13 parts, down from 13.6 in 2024.
What this looks like in Ventura County
Tony’s holds programmes from Honda and Acura, GM, Cadillac, Hyundai, Kia, FCA, Ford, Subaru, Tesla, Lucid and Rivian, all completed at our Oxnard shop at 497 Lambert St, and from VinFast, completed at our Ventura shop at 6680 Crescent St, Unit 1. For those makes, every auto body repair decision starts with the factory procedure. If you drive a Honda or Acura, our Honda certified body shop page covers what that certification means for your repair.
Both shops write estimates and repair collision damage for every make, with pickup and delivery throughout the region; a car estimated at one that needs the other is moved at no charge to you. Aluminum jobs go into the aluminum room at Oxnard.
Frequently asked questions
Can a bent frame rail be straightened?
Sometimes. In auto body repair it depends on the steel and the automaker’s procedure. Mild and some high-strength steels can often be straightened, but many automakers require ultra-high-strength parts to be replaced once they are deformed.
Why did my insurer write “repair” when the shop wrote “replace”?
Usually because repair time is a judgment call and replacement time comes from the database. California regulation 10 CCR 2695.8(f) requires the insurer’s estimate to allow for repairs made to accepted trade standards, and the shop documents the automaker’s procedure to show what those standards require on your car.
Is a new part always better than a repaired one?
No. A mild-steel panel put back to the factory procedure is a good auto body repair. Replacement matters most where the metal cannot be safely straightened or heated.
Can my insurer make me use aftermarket parts?
Only under conditions. In California, non-OEM crash parts have to be at least equal to OEM parts in kind, quality, safety, fit and performance, and they have to be disclosed on the estimate. General information, not legal advice.
Who decides whether a part is repaired or replaced?
The automaker’s repair procedure sets the rules, the shop documents the damage against those rules, and the insurer pays for repairs that meet accepted trade standards.
Can I bring my car to the Ventura shop?
Yes. Our Ventura shop at 6680 Crescent St, Unit 1 writes estimates and repairs collision damage for every make, and it is the VinFast certified location. If your car needs another manufacturer’s certified repair, or aluminum structural work in the aluminum room, we move it to Oxnard for that stage at no charge to you.
- Oxnard
- Ventura
- Camarillo
- Thousand Oaks
- Simi Valley
- Moorpark
- Santa Paula
- Ojai
- Port Hueneme
- Newbury Park
- Fillmore
- Somis
Two shops, one phone call. Estimates and collision repair at Oxnard and Ventura. Manufacturer-certified repairs are completed at Oxnard; VinFast certified repairs at Ventura. A car estimated at one shop that needs the other is moved at no charge to you.
Family owned since 1965
Get the fix-or-replace call in writing.
Bring the car to 497 Lambert St in Oxnard or 6680 Crescent St in Ventura. We will show you what the damaged parts are made of and what the factory procedure says to do with them.
Not drivable? Start with the estimate form and tell us where it is.
Oxnard OEM certified
497 Lambert St
Oxnard, CA 93036
Estimates and collision repair. Manufacturer-certified repairs (Honda, Acura, Ford, Subaru, GM, Cadillac, FCA, Hyundai, Kia, Rivian, Lucid, Tesla) are completed here.
Ventura VinFast certified
6680 Crescent St, Unit 1
Ventura, CA 93003
Estimates and collision repair for every make. VinFast certified repairs are completed here; a car that needs another manufacturer’s certified repair is moved to Oxnard at no charge to you. Rated 5.0 from 189 reviews on Carwise.
Sources
- I-CAR Repairability Technical Support, Kink vs. Bend (crn-635, July 27, 2017), including the 600 MPa rule.
- Repairer Driven News, “What does I-CAR say? Kink vs. bend instructions dead” (August 17, 2017), Jason Bartanen quote.
- Repairer Driven News, “Honda newsletter gives tips on where to find ultra-high-strength steel repair information” (July 15, 2026), covering American Honda’s The Joy of Repair, Summer 2026.
- FCA US LLC, Use of Heat position statement (December 1, 2025), via OEM1Stop.
- I-CAR RTS, Straightening and Heat: General Motors (crn-1364, May 20, 2020); Body Construction and Material Repair Guidelines: Kia (crn-653, August 8, 2017); Body Construction and Material Repair Guidelines: Subaru (crn-667, August 30, 2017).
- Tesla, Model Y Collision Repair Procedures, Cast Rear Under Body Repair Guidelines (service.tesla.com).
- Ford Motor Company, Collision Position Statement: Aluminum Structural Repair (October 1, 2025), via OEM1Stop.
- Mitchell, Collision Estimating Guide, Labor General Information; Society of Collision Repair Specialists, “Mitchell labor times” (January 2, 2019).
- Autobody News, “Enlyte’s 2026 Trends Report…” (June 8, 2026); CCC Intelligent Solutions, Crash Course 2026 (March 2026).
- California Code of Regulations, 10 CCR § 2695.8(f) and (g), Cornell LII; California Department of Insurance, legal opinion on OEM part designations (October 8, 2018).
This article describes manufacturer position statements, industry data and California claims regulations as published in September 2026. It is general information from a body shop, not legal advice; the manufacturer’s current repair procedure governs any repair.